Quality Inspection: Types, Process & Checklist for Factories

6 min read

By

TranZact Solutions Team

· Published

Hero Background
Functions of ERP System Explained

What is quality inspection?

Quality inspection is checking materials, parts or finished goods against a set standard (drawing, spec or sample), then accepting, reworking or rejecting them. Factories inspect at three points: incoming raw material at goods receipt, work in progress on the shop floor, and finished goods before dispatch. Each check is recorded with the batch, quantity accepted, quantity rejected and the reason. That record lets you trace a problem back to a supplier, machine or shift.

The standard can be a drawing, a spec sheet, an approved sample or the customer's written requirement. Inspection matters because a defect caught at the gate costs a phone call. The same defect found by your customer costs a rejection, a credit note and trust.

Quality inspection vs quality control vs quality assurance

People use these words as if they mean the same thing. They don't. Inspection is the check itself. Quality control uses those results to keep the process on track. Quality assurance is the whole system that stops defects happening.

Term

What it is

Example

Quality inspection

Checking a part or lot against the standard

Measuring 20 shafts from a lot at the gate

Quality control

Acting on inspection results to keep output in spec

Stopping a machine when the bore size drifts

Quality assurance

The overall system of procedures, training and checks

Written inspection plans, calibrated gauges, audits

Types of quality inspection (by stage)

The common "4 types" list is pre-production (incoming), during-production, pre-shipment (final) and container loading checks. In an Indian factory, add returned material inspection as a fifth.

Incoming (raw material) inspection at goods receipt

Material is checked at the gate before the GRN is made. Our GRN format guide shows where the result goes.

In-process inspection, including first-piece / first article

The first piece off a new setup is approved before the run continues. Regular checks after that catch tool wear before a whole batch goes wrong.

Final inspection before dispatch

Finished goods get one last check before they leave the factory.

Pre-shipment and container loading checks (when your buyer or importer asks for them)

An inspector, sometimes from a third-party agency, checks a sample of packed goods and watches the container being loaded.

Returned material inspection

Goods a customer sends back are checked to confirm the defect and find its cause. The result decides rework, scrap or replacement. It also tells you which batch to look at.

Where incoming inspection sits
  1. PO sent to the supplier

  2. Material arrives at the gate

  3. Stores and QC check the lot

  4. GRN for the accepted quantity

  5. Rejects returned with a debit note

Paper register, Excel or software: how to record inspections

A paper register is quick to start and needs no training. But when a customer complains, someone has to search old pages by hand to find the batch.

Excel is easier to search. It breaks when many batches and several users touch one file, and it doesn't update stock when you reject a lot.

Good software links each check to the GRN, the batch and the stock count, so a rejected lot never shows as usable stock. For a fuller buying view, see our quality control software buying guide.

How TranZact handles quality checks for manufacturers

TranZact is manufacturing AI software, trusted by 10,000+ manufacturers. AI runs your entire operations from enquiry to dispatch.

The purchase flow runs MRP report → indent → RFQ → PO → GRN → payment. Incoming inspection belongs at the GRN, where material enters stock.

Raw material and finished goods quality control come with the Dominate plan, listed on the pricing page as "Batch Tracking & QC". Batch-wise stock tracking starts at Scale+.

See the inventory management and production management pages for full feature lists. Accounting stays in Tally, and TranZact goes live in 2–3 weeks.

One honest limit: software doesn't replace the inspector. Quality control isn't part of the Grow or Scale+ plans.

Book a demo →

Quality inspection process: 7 steps

  1. Set the standard. Write the drawing, spec and acceptance criteria for each item.

  2. Decide the stage and frequency. Incoming, in-process or final, and how often.

  3. Pick 100% check or sampling. Base it on risk and lot size.

  4. Inspect and measure. Use the right gauge and the same method every time.

  5. Record the result per batch. Quantity accepted, quantity rejected and the reason.

  6. Act on rejects. Return, rework or scrap, and raise a debit note where needed.

  7. Review trends. Look at rejections by supplier, machine and shift every month.

Sampling and AQL in plain words

AQL means Acceptable Quality Level. It is the highest defect rate you will still accept, on average, for a lot. You agree it with your customer or supplier for each item.

Sampling is cheaper than checking every piece. A well-chosen sample gives a reliable answer much faster.

Worked example (illustrative numbers, not a standard table value): a lot of 2,000 machined bushes arrives. Your agreed plan says check 125 pieces. Accept the lot if 3 or fewer are defective; reject it if 4 or more are.

You find 2 defective bushes, so the lot is accepted. Find 5, and the lot goes back or gets a 100% sort. Take real limits from your customer's sampling table, such as ISO 2859-1.

100% check vs sampling: when each fits


100% check

Sampling to an AQL

Best for

Safety-critical or costly defects

Large lots of routine parts

Inspector time

High

Low

Lot decision

Every piece sorted

Accept or reject the whole lot

Methods: what inspectors actually check

A quality inspector checks goods against the standard, records the result and stops bad material moving on. The method depends on what can go wrong.

  • Visual: scratches, rust, burrs, colour, missing labels. Quick, and it suits every stage.

  • Dimensional: calipers, micrometers, plug and ring gauges. Suits machined and moulded parts.

  • Functional: does it fit, seal, switch on or hold pressure? Suits assemblies and finished goods.

  • Destructive testing: tensile, burst or peel tests on a few samples. Suits raw material and new suppliers.

Quality inspection checklist for each stage

Incoming

  • Material and quantity match the PO

  • Supplier test certificate received

  • Batch or lot number noted

  • Visual check done

  • Key dimensions measured

  • Accepted and rejected quantity recorded

In-process

  • First piece approved before the run

  • Critical dimensions checked at set intervals

  • Machine and operator noted on the record

Final

  • Appearance, dimensions and function checked

  • Packing and labels correct

  • Batch number matches the dispatch documents

Noting the batch at every stage is what makes batch tracking work when a complaint comes in.

What to do with rejected material

Move rejected stock to a marked area and tag it, so nobody issues it by mistake. Record the reason against the PO and batch.

Return supplier rejects with a purchase return and debit note, so stock and payables stay correct. Our purchase return guide covers the paperwork. In-house rejects go for rework or scrap.

Then track each supplier's rejection rate. It is the fairest input for vendor rating and supplier evaluation.

Want to see where the check fits between your GRN, your batches and your stock? Don't be the bottleneck. Become the AI-Run Factory.

Book a demo →

Check out other blogs

Hero Background
Become the
AI-Run Factory

Born in India. Building for the world.

Built by IIT & IIM founders

Hero Background
Become the
AI-Run Factory

Born in India. Building for the world.

Built by IIT & IIM founders

Hero Background
Become the
AI-Run Factory

Born in India. Building for the world.

Built by IIT & IIM founders